Car Routing

From FYM Wiki
Revision as of 19:42, 23 August 2020 by Danny252 (talk | contribs) (Add interchange info)
Jump to navigation Jump to search

Car routing, or determining how cars move from point A to point B, is the most important job a Yard Master has.

Train Symbols and Routes (TSARs)

Much like the Russian Czars of old, TSARs rule the FYM world. If it is not on a TSAR is didn't (shouldn't) happen.

See Train Symbols and Routes (TSARs) for more information about TSARs.

The first thing to do when trying to learn how traffic is handled in your yard is to read the TSARs that pass through your yard. All of them. Notes specifically for your yard will (most of the time) have @@[Yard #] - [Name] in the TSAR notes. When reviewing the TSARS for your yard you want to look for the following:

  • "works here", "work as needed", or some variant - This typically indicates that you should pull off any cars for the local industries in your yard. This may also mean that you can add cars for destinations down the line to this train.
  • "setout" - This typically indicates that you are to pull a block of cars off this train for inclusion on a different train passing through later.
  • "pickup" - This typically indicates that you are to add cars from an earlier setout.
  • "check engines" or "fuel power" - If you have fueling facilities in your yard you should refuel the engine if they are below about 500 miles left.

TSARs may also contain information about how many and what type of engines should be used for a train and the types and number of cars for unit trains.

Locals

Local trains form the start or end of a car's journey from source to destination and often traverse very short distances. Locals carry cars from larger sorting yards to smaller yards for delivery to local industries and then back to the sorting yard. In some cases this may lead to a situation where cars will travel through your yard to the sorting yard and then come back to your yard on a local train.

When reviewing TSARs make sure you have a good understanding of locals that run to and from your yards.

Interchange

As soon as a car needs to move from an origin served by one railroad to a destination served by another, it will need to be interchanged or transferred between railroads. A car will need to be interchanged more than once if there is no direct connection between its origin and destination railroads. For example, a car travelling from an origin on the Florida East Coast railroad to a destination in California served by BNSF cannot be transferred directly between those railroads - the FEC only has lines in Florida, while BNSF does not get any further east than Birmingham, AL. Instead, the FEC interchanges directly with NS or CSX, either of which can transport the car to a suitable interchange point for BNSF.

In real life, almost all cars are eligible for interchange, regardless of their owner (railroads, railroad pools, or private owner); FYM assumes that all cars are eligible to travel to any destination.

Interchange can be completed in several ways, depending on the location and volume of traffic:

  • Cars can be left at an interchange siding or yard at a junction between two railroads, and later collected by the other railroad.
  • A transfer train may travel directly between yards of the two corresponding railroads, avoiding the delay and capacity constraints of interchange tracks.
  • A terminal railroad can act as an intermediary, receiving cars from one railroad and transferring to another (e.g. the BRC or IHB in Chicago, or TRRA in St Louis). These are often jointly owned by larger railroads.
  • A run-through train can proceed directly from one railroad to another, with its destination being some way beyond the interchange location. Unit trains many continue from origin to destination without even stopping to change locomotives, to further streamline the process.

In general, a railroad will avoid transferring cars to another railroad needlessly early, as a shorter route will reduce the fees they can charge - this is particularly relevant for rival railroads serving the same area, such as CSX/NS, or BNSF/KCS/UP. However, railroads will not resort to ridiculously roundabout routings via small branchlines - these lines lack the capacity to handle any significant amounts of interchange, and it would be extremely costly to use such routes unnecessarily. For railroads that are not highly competitive with one another, interchange routings are typically agreed to make best use of high capacity lines and yards, and to avoid highly unbalanced car flows (i.e. many cars arriving via one route, but returning via another).

Reciprocal Switching

In many major cities, and other areas served by multiple railroads, an industry is able to route cars via more than one railroad, even if cars are only delivered by a single railroad. This arrangement is referred to as reciprocal switching, as the arrangement often allows both railroads to equally access one another's customers in a reciprocal fashion. In FYM, this is represented by an industry being covered by multiple map IDs, one for each railroad involved. In these cases, all railroads have equal access - one railroad can interchange cars for the customer to the terminating railroad, and the customer can decide which railroad will take the car away to its final destination. Not all industries within a given area will necessarily be covered by reciprocal switching arrangements; these are often complex and can be based on what railroads historically served a customer, forced upon railroads during mergers to encourage competition, or negotiated by a major new customer.

A notably large example of this sort of arrangement are the Conrail areas in MI, NJ, and PA, which are given the railroad IDs CRMI, CRNJ, and CRSJ (South NJ/PA) in FYM. Following the joint purchase of Conrail by CSXT and NS, these locations were kept as joint service areas, with both railroads contributing to servicing these customers. As such, cars to and from any of the CRxx railroad destinations can be routed via either CSXT or NS.

Canadian Interswitching

In Canada, the concept of interswitching is a legal requirement similar to reciprocal switching in the US, applying mainly to CN and CP. By law, all customers within 30km of an interchange have the right to route their cars via whichever railroad they choose. In the prairie provinces of AB, SK, and MB, this distance was increased to 160km in 2014, in an effort to encourage competition for grain traffic originating in these areas. However, it is worth noting that few industries far from an interchange take advantage of this limit, with the threat of the competing railroad being given the traffic sufficient to keep rates low and service quality high.

Finding interchange routings

The TSARs can often give hints or instructions on interchange routings - at the very least, they indicate where interchange occurs.

Online tools or guides for interchange routings are available for several railroads:

  • BNSF allows interchange routings to be queried for CN, CSXT, and CP.
  • CSX's Junction Look-Up shows preferred interchange routings to BNSF, CN, KCS, and UP.
  • UP's Interline Routing Agreements show routings for interchange with CP, CSXT, and NS, along with the Mexican railroads, FXE and KCS de Mexico.
  • For Canada, both CN and CP publish full lists of interswitching locations - i.e. all locations at which an interchange can occur, as desired by the customer.